1. Home
  2. Support
  3. Firmware / Software Updates
  4. MTX Editor V1.1.1 for Win8/7 and firmware V1.11 (Previous version)

MTX Editor V1.1.1 for Win8/7 and firmware V1.11 (Previous version)

Important Notice

  • Please refer to the MTX Editor User's Manual on how to update the MTX Firmware. 
    * Chapter7.Dialog boxes >>“Update Firmware” dialog box
  • The internal data compatibility of the device will be lost if the firmware of devices is updated from V1.03 to V1.11. Please ensure that the MTX is synchronized and saved to MTX Editor V1.0.1 as a project file before performing the firmware update in order to ensure that your project data is not lost, then perform the firmware upgrade using the latest version of MTX Editor. Please ensure that the device is initialized after the update. After updating, open the previously saved project file using the latest MTX Editor and re-synchronize to the updated devices.
  • When initializing Dante devices (MTX5-D / XMV4280-D / XMV4140-D / XMV8280-D / XMV8140-D), please ensure that all other Dante devices on the network are disconnected or powered off. Otherwise initialization could take longer than necessary.
  • To prevent damage to the device or the SD memory card as well as loss of data, do not remove or insert the SD memory card while the device is on.
  • Although MTX Editor shows 'Completed' after updating firmware, please do not turn off the power of the MTX until the indicators on the front panel have stopped blinking.
  • The device may not be restarted automatically after completing the firmware update. Please ensure that the latest version number is displayed in Version area of Device Information dialog box by pressing the [Refresh] button. After updating the firmware, if the previous version number is displayed, turn the device off then on again, and re-check the version number again.
  • Please do not use the EEE function (*) of network switches in a Dante network. Although power management should be negotiated automatically in switches that support EEE, some switches do not perform the negotiation properly. This may cause EEE to be enabled in Dante networks when it is not appropriate, resulting in poor synchronization performance and occasional dropouts. Therefore we strongly recommend that: 
    1.If you use managed switches, ensure that they allow EEE to be disabled. Make sure that EEE is disabled on all ports used for real-time Dante traffic. 
    2.If you use unmanaged switches, make sure to not use network switches that support the EEE function, since EEE operation cannot be disabled in these switches. 
    * EEE (Energy Efficient Ethernet) is a technology that reduces switch power consumption during periods of low network traffic. It is also known as Green Ethernet and IEEE802.3az.

   This zip file includes the following software 
　  - MTX Editor V1.1.1 
　  - MTX3 Firmware V1.11 
　  - MTX5-D Firmware V1.11 
　  - EXi8 Firmware V1.11 
　  - EXo8 Firmware V1.11 
　  - XMV4140 Firmware V1.11 
　  - XMV4280 Firmware V1.11 
　  * There is no need to update Dante Firmware for MTX5-D at this time.

Main Revisions and Enhancements

MTX Editor V1.1.1

New Features

  • Now supports the following devices: 
    MTX5-D 
    XMV4280-D / XMV4140-D 
    XMV8280 / XMV8140 / XMV8280-D / XMV8140-D 
    EXi8 / EXo8 
    DCP4S-US/EU 
    DCP4V4S-US/EU 
  • Setup of Dante devices (MTX5-D / XMV4280-D / XMV4140-D / XMV8280-D / XMV8140-D) can now be configured from MTX Editor.
  • A maximum of four MTX systems can be set up and controlled in one project file.
  • Preset Links can be created for preset recall across MTX systems within the same project file.
  • Added the "XMV" screen and "EXo8" screen, which provides display and setup for the parameters of XMV and EXo8.
  • Added the following functions on the Project screen - 
    Set up for the XMV DIMMER function. 
    Display of the XMV [OUTPUT SETUP].
  • You can switch the meter point of the input channel between EQ OUT and POST ON (default).
  • When a Preset is recalled, you can set the Scheduler function to be disabled in the "Preset" dialog box.
  • Added display of the serial number for devices, and battery power status (for a device that contains batteries) in the "Device Information" dialog box.
  • By using the switches of the DCP1V4S-US/EU, it is possible to change the control assignment of the knob, letting you use the knob for two or more functions such as Source Select.
  • Added the function of word clock setup.
  • Added an emergency mode – 
    A Preset can be assigned as an emergency mode, to be triggered by GPI. 
    This can be utilized for muting a sound system in the case of emergency, such as the outbreak of a fire, etc. 
  • Added VXC series and VXS series to the library for the SPEAKER PROCESSOR.

Improvements

  • Improved the functions of SD Song Select & Play.
  • The initial saved Project file destination was changed to My Documents. Previously this was set to either C:\Program Files or C:\Program Files (x86).

Fixed bugs

  • Solved a problem when settings are taken into MTX Editor using the "Go Online From Devices" dialog box from the MTX system (of two or more MTX units) in the state where GPI Out is set up in the "Scheduler" dialog, the GPI Out settings of the second and subsequent MTX3 units will be incorrectly displayed.
  • Solved a problem while playing back music and sound files which have been saved to an SD memory card, and SD PLAY recalled a preset having a "No Assign" setting or an event was called up having a SONG setting of "No Assign," the SD card playback was stopped rather than continuing unaffected.

MTX3 Firmware V1.11

Fixed Bugs

  • Solved a problem in which the events set up in the Scheduler dialog box of MTX Editor could not be started until 60 seconds have elapsed after synchronization is completed.
  • Solved a problem in which, when no playable sound files have been saved to an SD memory card, alert number 56 occurs.
  • Solved a problem in which the Wireless DCP display is not updated automatically, when the Wireless DCP library has been changed in MTX Editor.
  • Solved a problem in which an MTX3 is displayed as an unknown device in the [Alert] tab of MTX Editor, and the Log file stored in the MTX.

Known issues

  • A log file may not be successfully retrieved using the "Get Log" dialog box of MTX Editor. In this case, turn the device off and then on again and attempt to retrieve the log file again.
  • The device may not be restarted automatically after running the Firmware Update. If the device is not restarted when “Complete” is displayed in the Status column, please turn the device off and then on again.

MTX5-D Firmware V1.11

V1.11 is the first released version.

Known Issues

  • A log file may not be successfully retrieved using the "Get Log" dialog box of MTX Editor. In this case, turn the device off and then on again and attempt to retrieve the log file again.
  • The device may not be restarted automatically after running the Firmware Update. If the device is not restarted when “Complete” is displayed in the Status column, please turn the device off and then on again.
  • After making a Dante patch setting and synchronizing from MTX Editor "To Device," the changes may not occur in the MTX5-D. If this occurs, turn the MTX5-D off and then on again.

XMV Firmware V1.11

Fixed Bug

  • Solved a problem in which, when the power of an XMV connected to an MTX via a NETWORK connector, is turned on and alert number 102 may be recorded to the MTX Editor as a log entry.
  • Solved a problem when muting for temperature protection occurs, alert number 106 is not displayed.

Known Issue

  • The device may not be restarted automatically after running the Firmware Update. If the device is not restarted when “Complete” is displayed in the Status column, please turn the device off and then on again.

EXi8/EXo8 Firmware V1.11

Fixed Bug

  • Solved a problem when the EXi8/EXo8 is started two or more times in succession, with DIP switches 7 and 8 set to "INITIALIZE," alert numbers 2 and 7 will display.

Known Issue

  • The EXi8/EXo8 may not be restarted automatically after running the Firmware Update. If the device is not restarted when “Complete” is displayed in the Status column, please turn the device off and then on again.

    System Requirements

    OS Windows 8 Windows 7 (SP1)
    CPU Core i3/5 or better 
    		Core i3/5 or better
    Memory 4GB or more 
    HDD 150 MB or more
    Display 1024 x 768 pixels or higher
    Other Bonjour must be installed, Ethernet(1000BASE-T or higher)

    License Agreement and Download File

    ATTENTION

    PLEASE READ THIS SOFTWARE LICENSE AGREEMENT ("AGREEMENT") CAREFULLY BEFORE USING THIS SOFTWARE. YOU ARE ONLY PERMITTED TO USE THIS SOFTWARE PURSUANT TO THE TERMS AND CONDITIONS OF THIS AGREEMENT. THIS AGREEMENT IS BETWEEN YOU (AS AN INDIVIDUAL OR LEGAL ENTITY) AND YAMAHA CORPORATION ("YAMAHA").

    BY DOWNLOADING OR INSTALLING THIS SOFTWARE OR OTHERWISE RENDERING IT AVAILABLE FOR YOUR USE, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE. IF YOU DO NOT AGREE WITH THE TERMS, DO NOT DOWNLOAD, INSTALL, COPY, OR OTHERWISE USE THIS SOFTWARE. IF YOU HAVE DOWNLOADED OR INSTALLED THE SOFTWARE AND DO NOT AGREE TO THE TERMS, PROMPTLY DELETE THE SOFTWARE.

    GRANT OF LICENSE AND COPYRIGHT

    Yamaha hereby grants you the right to use the programs and data files composing the software accompanying this Agreement, and any programs and files for upgrading such software that may be distributed to you in the future with terms and conditions attached (collectively, “SOFTWARE”), only on a computer, musical instrument or equipment item that you yourself own or manage. While ownership of the storage media in which the SOFTWARE is stored rests with you, the SOFTWARE itself is owned by Yamaha and/or Yamaha’s licensor(s), and is protected by relevant copyright laws and all applicable treaty provisions.

    RESTRICTIONS

    • You may not engage in reverse engineering, disassembly, decompilation or otherwise deriving a source code form of the SOFTWARE by any method whatsoever.
    • You may not reproduce, modify, change, rent, lease, or distribute the SOFTWARE in whole or in part, or create derivative works of the SOFTWARE.
    • You may not electronically transmit the SOFTWARE from one computer to another or share the SOFTWARE in a network with other computers.
    • You may not use the SOFTWARE to distribute illegal data or data that violates public policy.
    • You may not initiate services based on the use of the SOFTWARE without permission by Yamaha Corporation.

    Copyrighted data, including but not limited to MIDI data for songs, obtained by means of the SOFTWARE, are subject to the following restrictions which you must observe.

    • Data received by means of the SOFTWARE may not be used for any commercial purposes without permission of the copyright owner.
    • Data received by means of the SOFTWARE may not be duplicated, transferred, or distributed, or played back or performed for listeners in public without permission of the copyright owner.
    • The encryption of data received by means of the SOFTWARE may not be removed nor may the electronic watermark be modified without permission of the copyright owner.

    TERMINATION

    If any copyright law or provisions of this Agreement is violated, the Agreement shall terminate automatically and immediately without notice from Yamaha. Upon such termination, you must immediately destroy the licensed SOFTWARE, any accompanying written documents and all copies thereof.

    DOWNLOADED SOFTWARE

    If you believe that the downloading process was faulty, you may contact Yamaha, and Yamaha shall permit you to re-download the SOFTWARE, provided that you first destroy any copies or partial copies of the SOFTWARE that you obtained through your previous download attempt. This permission to re-download shall not limit in any manner the disclaimer of warranty set forth in Section 5 below.

    DISCLAIMER OF WARRANTY ON SOFTWARE

    You expressly acknowledge and agree that use of the SOFTWARE is at your sole risk. The SOFTWARE and related documentation are provided "AS IS" and without warranty of any kind. NOTWITHSTANDING ANY OTHER PROVISION OF THIS AGREEMENT, YAMAHA EXPRESSLY DISCLAIMS ALL WARRANTIES AS TO THE SOFTWARE, EXPRESS, AND IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS. SPECIFICALLY, BUT WITHOUT LIMITING THE FOREGOING, YAMAHA DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS, THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE, OR THAT DEFECTS IN THE SOFTWARE WILL BE CORRECTED.

    LIMITATION OF LIABILITY

    YAMAHA’S ENTIRE OBLIGATION HEREUNDER SHALL BE TO PERMIT USE OF THE SOFTWARE UNDER THE TERMS HEREOF. IN NO EVENT SHALL YAMAHA BE LIABLE TO YOU OR ANY OTHER PERSON FOR ANY DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, EXPENSES, LOST PROFITS, LOST DATA OR OTHER DAMAGES ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THE SOFTWARE, EVEN IF YAMAHA OR AN AUTHORIZED DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. In no event shall Yamaha's total liability to you for all damages, losses and causes of action (whether in contract, tort or otherwise) exceed the amount paid for the SOFTWARE.

    THIRD PARTY SOFTWARE

    Third party software and data ("THIRD PARTY SOFTWARE") may be attached to the SOFTWARE. If, in the written materials or the electronic data accompanying the Software, Yamaha identifies any software and data as THIRD PARTY SOFTWARE, you acknowledge and agree that you must abide by the provisions of any Agreement provided with the THIRD PARTY SOFTWARE and that the party providing the THIRD PARTY SOFTWARE is responsible for any warranty or liability related to or arising from the THIRD PARTY SOFTWARE. Yamaha is not responsible in any way for the THIRD PARTY SOFTWARE or your use thereof.

    • Yamaha provides no express warranties as to the THIRD PARTY SOFTWARE. IN ADDITION, YAMAHA EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, as to the THIRD PARTY SOFTWARE.
    • Yamaha shall not provide you with any service or maintenance as to the THIRD PARTY SOFTWARE.
    • Yamaha is not liable to you or any other person for any damages, including, without limitation, any direct, indirect, incidental or consequential damages, expenses, lost profits, lost data or other damages arising out of the use, misuse or inability to use the THIRD PARTY SOFTWARE.

    U.S. GOVERNMENT RESTRICTED RIGHTS NOTICE:

    The Software is a "commercial item," as that term is defined at 48 C.F.R. 2.101 (Oct 1995), consisting of "commercial computer software" and "commercial computer software documentation," as such terms are used in 48 C.F.R. 12.212 (Sept 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.72024 (June 1995), all U.S. Government End Users shall acquire the Software with only those rights set forth herein

    GENERAL

    This Agreement shall be interpreted according to and governed by Japanese law without reference to principles of conflict of laws. Any dispute or procedure shall be heard before the Tokyo District Court in Japan. If for any reason a court of competent jurisdiction finds any portion of this Agreement to be unenforceable, the remainder of this Agreement shall continue in full force and effect.

    COMPLETE AGREEMENT

    This Agreement constitutes the entire agreement between the parties with respect to use of the SOFTWARE and any accompanying written materials and supersedes all prior or contemporaneous understandings or agreements, written or oral, regarding the subject matter of this Agreement. No amendment or revision of this Agreement will be binding unless in writing and signed by a fully authorized representative of Yamaha.

    mtx_editor111_firm111-2.zip (57.9MB)

    Previous versions

    1. Home
    2. Support
    3. Firmware / Software Updates
    4. MTX Editor V1.1.1 for Win8/7 and firmware V1.11 (Previous version)