EMX7/EMX5

EMX7 EMX5
I/O Inputs TOTAL 12 channels : 8 Mono (MIC/LINE), 4 Stereo (LINE) TOTAL 12 channels : 8 Mono (MIC/LINE), 4 Stereo (LINE)
Phantom power +48 V +48 V
Outputs SPEAKERS [A, B], AUX1 SEND, AUX2 SEND, STEREO OUT [L, R], REC OUT [L, R] SPEAKERS [A, B], AUX1 SEND, AUX2 SEND, STEREO OUT [L, R], REC OUT [L, R]
Control and others FOOT SWITCH : Effect Mute on/off FOOT SWITCH : Effect Mute on/off
Bus Stereo: 1, AUX: 2 (Including FX) Stereo: 1, AUX: 2 (Including FX)
Input Channel Function PAD 30 dB (CH1-4) 30 dB (CH1-4)
Hi-Z Supported (CH4) Supported (CH4)
HPF 80 Hz, -12 dB/oct. (CH1–3) 80 Hz, -12 dB/oct. (CH1–3)
COMP 1-knob COMP (CH1–4) 1-knob COMP (CH1–4)
EQ HIGH 10 kHz +15 dB / -15 dB (Shelving) 10 kHz +15 dB / -15 dB (Shelving)
EQ MID 2.5 kHz +15 dB / -15 dB (Peaking) 2.5 kHz +15 dB / -15 dB (Peaking)
EQ LOW 100 Hz +15 dB / -15 dB (Shelving) 100 Hz +15 dB / -15 dB (Shelving)
On-board processors DSP SPX Algorithm 24 programs, Feedback suppressor, Graphic equalizer, Speaker processor SPX Algorithm 24 programs, Feedback suppressor, Master EQ, Monitor EQ
On-board amplifiers Maximum output power @4ohms 1kHz THD+N less than 10% (CEA2006) : 710 W + 710 W, 1kHz THD+N less than 1% (CEA2006) : 600 W + 600 W 1kHz THD+N less than 10% (CEA2006) : 630 W + 630 W, 1kHz THD+N less than 1% (CEA2006) : 500 W + 500 W
Maximum output power @8ohms 1kHz THD+N less than 10% (CEA2006) : 500 W + 500 W, 1kHz THD+N less than 1% (CEA2006) : 400 W + 400 W 1kHz THD+N less than 10% (CEA2006) : 460 W + 460 W, 1kHz THD+N less than 1% (CEA2006) : 370 W + 370 W
Level Meter 2 × 12 points LED meter (-30, -25, -20, -15, -10, -6, -3, 0, +3, +6, +10, PEAK) 2 × 7 points LED meter (-20, -10, -6, 0, +6, +10, PEAK)
Frequency response Input to SPEAKERS : +1 dB/-3 dB (40 Hz to 20 kHz), Input to STEREO OUT, AUX1 SEND, AUX2 SEND : +0.5 dB/-1 dB (20 Hz to 20 kHz) , refer to the nominal output level @ 1 kHz Input to SPEAKERS : +1 dB/-3 dB (40 Hz to 20 kHz), Input to STEREO OUT, AUX1 SEND, AUX2 SEND : +0.5 dB/-1 dB (20 Hz to 20 kHz) , refer to the nominal output level @ 1 kHz
Total harmonic distortion Input to SPEAKERS: MIC/LINE =LINE (CH1–4): 0.1% @ 10 W (40 Hz to 20 kHz), 0.04% @ 65 W (1 kHz) ; Input to STEREO OUT, AUX1 SEND, AUX2 SEND: MIC/LINE =LINE (CH1–4): 0.02% @ +14 dBu (20 Hz to 20 kHz), 0.007% @ +20 dBu (1 kHz), (THD+N, measured with 22 kHz LPF) Input to SPEAKERS: 0.1% @ 10 W (40 Hz to 20 kHz), 0.05% @ 50 W (1 kHz) ; Input to STEREO OUT, AUX1 SEND, AUX2 SEND: 0.03% @ +14 dBu (20 Hz to 20 kHz), 0.007% @ +20 dBu (1 kHz), (THD+N, measured with 22 kHz LPF)
Hum & noise level Equivalent input noise -117 dBu (Noise is measured with A-weighting filter) -117 dBu (Noise is measured with A-weighting filter)
Residual output noise Input to SPEAKERS : -70 dBu(40Hz to 20kHz, STEREO MASTER LEVEL: min); Input to STEREO OUT, AUX1 SEND, AUX2 SEND : -82dBu(20Hz to 20kHz, STEREO MASTER LEVEL: min) (Noise is measured with A-weighting filter) Input to SPEAKERS : -70 dBu(40Hz to 20kHz, STEREO MASTER LEVEL: min); Input to STEREO OUT, AUX1 SEND, AUX2 SEND : -82dBu(20Hz to 20kHz, STEREO MASTER LEVEL: min) (Noise is measured with A-weighting filter)
Crosstalk -85 dB (1 kHz, Measured with 1 kHz band pass filter) -85 dB (1 kHz, Measured with 1 kHz band pass filter)
Protection circuit Load protection DC-fault DC-fault
Amplifier protection Over heat protection, Over current protection, Integral power protection Over heat protection, Over current protection, Integral power protection
Power supply protection Over heat protection, Over current protection Over heat protection, Over current protection
Power requirements AC 100-240V, 50Hz/60Hz AC 100-240V, 50Hz/60Hz
Power consumption 45 W (Idle) / 250 W (1/8 Power) 42 W (Idle) / 210 W (1/8 Power)
Dimensions W 465 mm (18 5/16") 465 mm (18 5/16")
H 308 mm (12 1/8") 308 mm (12 1/8")
D 325 mm (12 13/16") 325 mm (12 13/16")
Net weight 9.5 kg (20.9 lbs) 9.5 kg (20.9 lbs)
Accessories Owner’s Manual, Technical Specifications, AC power cord (2.5 m) Owner’s Manual, Technical Specifications, AC power cord (2.5 m)
Options Foot switch: FC5, Rack-mount brackets: RK-EMX7 Foot switch: FC5, Rack-mount brackets: RK-EMX7
Others Operating Temperature : 0 to +40℃ Operating Temperature : 0 to +40℃
  • (0 dBu = 0.775 Vrms, Output impedance of signal generator (Rs) = 150 Ω All level controls are at their maximum position if not specified.)

Input Characteristics

Input Jack MIC/LINE Hi-Z Actual Load Impedance For Use with Nominal Input Level Connector
Sensitivity *1 Nominal Level (▼ Position) *2 Max. Before Clip
CH 1–4 XLR MIC - 3 kΩ 50–600 Ω Mics -60 dBu (0.775 mV) -43 dBu (5.48 mV) -15 dBu (138 mV) Combo jack *3 (Balanced)
LINE - -30 dBu (24.5 mV) -13 dBu (173 mV) +15 dBu (4.36 V)
Phone MIC - 8 kΩ 600 Ω Lines -50 dBu (2.45 mV) -33 dBu (17.3 mV) -5 dBu (436 mV)
LINE - -20 dBu (77.5 mV) -3 dBu (548 mV) +25 dBu (13.8 V)
CH 4 (Hi-Z) Phone MIC ON 1 MΩ 10 kΩ Lines -50 dBu (2.45 mV) -33 dBu (17.3 mV) -5 dBu (436 mV) Phone jack *4 (Unbalanced)
LINE -20 dBu (77.5 mV) -3 dBu (548 mV) +20 dBu (7.75 V)
CH 5/6, 7/8 XLR - - 3 kΩ 50–600 Ω Mics -60 dBu (0.775 mV) -43 dBu (5.48 mV) -15 dBu (138 mV) XLR-3-31 *5 (Balanced)
Phone 10 kΩ 600 Ω Lines -20 dBu (77.5 mV) -3 dBu (548 mV) +25 dBu (13.8 V) Phone jack *4 (Unbalanced)
CH 9/10, 11/12 XLR - - 3 kΩ 50–600 Ω Mics -60 dBu (0.775 mV) -43 dBu (5.48 mV) -15 dBu (138 mV) XLR-3-31 *5 (Balanced)
Pin 10 kΩ 600 Ω Lines -8 dBu (316 mV) +10 dBu (2.45 V) +25 dBu (13.8 V) RCA pin (Unbalanced)
CH 11/12 Mini jack - - 10 kΩ 600 Ω Lines -8 dBu (316 mV) +10 dBu (2.45 V) +25 dBu (13.8 V) Stereo mini jack *6 (Unbalanced)

(0 dBu = 0.775 Vrms)
*1 Sensitivity is the lowest level that will produce an output of +4 dBu (1.228 V) or the nominal output level when the unit is set to maximum gain. (All level controls are at their maximum position.)
*2 Level controls setting : Channel level controls are at their t position. Master level controls are at their maximum position.
*3 1&Sleeve = GND, 2&Tip = HOT, 3&Ring = COLD
*4 Tip = Signal, Sleeve = GND
*5 1 = GND, 2 = HOT, 3 = COLD
*6 Tip = LEFT, Ring = RIGHT, Sleeve = GND

Output Characteristics

Output Jack Actual Source Impedance For Use with Nominal Output level Connector
Nominal Max. Before Clip
STEREO OUT L, R 600 Ω 10 kΩ Lines +4 dBu (1.228 V) +20 dBu (7.75 V) Phone jack *1 (Impedance balanced)
AUX SEND 1, 2 600 Ω 10 kΩ Lines +4 dBu (1.228 V) +20 dBu (7.75 V) Phone jack *1 (Impedance balanced)
REC OUT L, R 600 Ω 10 kΩ Lines -10 dBV (0.308 V) +18 dBV (7.75 V) RCA pin (Unbalanced)

(0 dBu = 0.775 Vrms 0 dBV = 1.00 Vrms)
*1 Tip = HOT, Ring = COLD, Sleeve = GND

Speaker Output Characteristics

Output Jack Actual Source Impedance For Use with Nominal Output level Connector
1 kHz THD+N < 1% (CEA2006) 1 kHz THD+N < 10% (CEA2006)
SPEAKERS A, B < 0.1 Ω 4 Ω Speakers 600 W (EMX7),
500 W (EMX5)
710 W (EMX7),
630 W (EMX5)
speakON NL4 *1
Phone jack *2
8 Ω Speakers 400 W (EMX7),
370 W (EMX5)
500 W (EMX7),
460 W (EMX5)

(0 dBu = 0.775 Vrms)
*1 1+ = Positive, 1- = Negative
*2 Tip = Positive, Sleeve = Negative