NUAGE
NUAGE FADER (Ncs500-FD)
General Specifications
Fader Stroke | 100mm |
---|---|
Fader Resolution (+12 to -∞dB) | 1024steps |
Power Requirements | 40W |
Power Consumption | US/Canada: 120V 60Hz, Japan: 100V 50/60Hz, China: 110-240V 50/60Hz, Korea: 220V 60Hz, Other: 110-240V 50/60Hz |
Operating Temperature Range | 0℃ ~ 40℃ |
Storage Temperature Range | -20℃ ~ 60℃ |
Dimensions (W x D x H) | 581 x 720 x 156mm (22-7/8" x 28-3/8" x 6-1/8") |
Net Weight | 17.8kg (39.2lb) |
Included Accessories | Power cable, Brackets (2), Getting Started Guide |
* All level controls are the nominal position. Output impedance of signal generator:150ohms
Control I/O Characteristics
Terminal | Format | Connector in Console |
---|---|---|
Network | IEEE802.3 (10Base-T/100Base-TX) | RJ-45 |
REMOTE | RS-232C | D-SUB Connector 9P (Male) |
NUAGE MASTER (Ncs500-CT)
General Specifications
Power Requirements | 30W |
---|---|
Power Consumption | US/Canada: 120V 60Hz, Japan: 100V 50/60Hz, China: 110-240V 50/60Hz, Korea: 220V 60Hz, Other: 110-240V 50/60Hz |
Operating Temperature Range | 0℃ ~ 40℃ |
Storage Temperature Range | -20℃ ~ 60℃ |
Dimensions (W x D x H) | 354 x 720 x 161mm (13-7/8" x 28-3/8" x 6-3/8") |
Net Weight | 10.0kg (22.0lb) |
Included Accessories | Jog wheel, Power cable, Brackets (2), Getting Started Guide |
Electrical Characteristics
All level controls are the nominal position. Output impedance of signal generator:150ohms. 0dBu = 0.775Vrms
Input | Output | RL | Conditions | ||
---|---|---|---|---|---|
Frequency Response | TO PHONES | Phones A or B | 8Ω | Phones level control max, Input level +4dBu(typ), 20Hz-20kHz, ref to the nominal output level @1kHz |
+0.5, -3dB |
Total Harmonic Distortion *1 | TO PHONES | Phones A or B | 8Ω | +4dB@20Hz-20kHz, Phones level control max | 0.04% |
Hum&Noise *2 | TO PHONES | Phones A or B | 8Ω | Residual output noise, Phones level control min | -100dBu |
Crosstalk@1kHz *3 | CH L | Phones out CH R | - | L/R, adjacent inputs | -80dB |
CH R | Phones out CH L | - |
Analog Input Characteristics
Input Terminals | Actual Load Impedance | For Use With Nominal | GAIN | Input level | Connector in Console | |
---|---|---|---|---|---|---|
Nominal | Max. before clip | |||||
TO PHONES | 20KΩ (BAL) | 150Ω Lines | 0dB | +4dBu (1.23 V) |
+30dBu (24.56 V) |
XLR3-31type connectors *4 |
Analog Output Characteristics
Output Terminals | Actual Source Impedance | For Use With Nominal | Output level | Connector in Console | |
---|---|---|---|---|---|
Nominal | Max. before clip | ||||
PHONES A | 100Ω | 8Ω Phones | 4mW | 25mW | Stereo Phone Jack (TRS) (Unbalanced) *5 |
40Ω Phones | 12mW | 75mW | |||
PHONES B | 100Ω | 8Ω Phones | 4mW | 25mW | Stereo Phone Mini Jack (TRS) (Unbalanced) *5 |
40Ω Phones | 12mW | 75mW | |||
TALKBACK OUT | 75Ω | 600Ω Lines | +4dBu (1.23 V) |
+24dBu (12.3 V) |
XLR-3-32 type (Balanced) *4 |
Control I/O Characteristics
Terminal | Format | Connector in Console |
---|---|---|
NETWORK | IEEE802.3 (10Base-T/100Base-TX) | RJ-45 |
REMOTE | RS-232C | D-SUB Connector 9P (Male) |
Appendix
*1. Total Harmonic Distortion is measured with 80kHz LPF.
*2. Hum & Noise are measured with A-weighting filter and 30kHz LPF.
*3. Crosstalk is measured with a -30dB/octave filter @22kHz.
*4. XLR-3-31 and XLR-3-32 type connectors are balanced.(1=GND, 2=HOT, 3=COLD)
*5. PHONES stereo phone jack is unbalanced. (Tip=LEFT, Ring=RIGHT, Sleeve=GND)
NUAGE I/O (Nio500-D16/Nio500-A16/Nio500-A8D8)
General Specifications
Sampling Frequency | Internal | 44.1kHz/48kHz/88.2kHz/96kHz/176.4kHz/192kHz | ||
---|---|---|---|---|
External | 44.1kHz +4.1667%/+0.1%/-0.1%/-4.0% |
±200ppm | ||
48kHz +4.1667%/+0.1%/-0.1%/-4.0% |
±200ppm | |||
88.2kHz +4.1667%/+0.1%/-0.1%/-4.0% |
±200ppm | |||
96kHz +4.1667%/+0.1%/-0.1%/-4.0% |
±200ppm | |||
176.4kHz +4.1667%/+0.1%/-0.1%/-4.0% |
±200ppm | |||
192kHz +4.1667%/+0.1%/-0.1%/-4.0% |
±200ppm | |||
Frequency Response | ±0.5dB, 20Hz-20kHz,ref to the nominal output level @1kHz, Input&Output Gain:0dB, Input level +4dBu(typ) | |||
THD+N *1 | Less than 0.005%, input to output, GAIN:0dB | |||
Dynamic Range | 120dB typ.,ADC 120dB typ.,DAC |
|||
Crosstalk@1kHz | -100dB, CH1-16 , adjacent inputs | |||
Power Requirements (wattage) | NUAGE I/O 16D: 51W NUAGE I/O 16A: 51W NUAGE I/O 8A8D: 51W |
|||
Power Requirements (voltage and hertz) | US/Canada: 120V 60Hz Japan: 100V 50/60Hz China: 110-240V 50/60Hz Korea: 220V 60Hz Other: 110-240V 50/60Hz |
|||
Dimensions (W x D x H) | 480 x 369 x 88 mm (18-7/8" x 14-1/2" x 3-1/2") | |||
Net Weight | NUAGE I/O 16D: 6.4kg(14.1lb) NUAGE I/O 16A: 6.7kg(14.1lb) NUAGE I/O 8A8D: 6.7kg(14.8lb) |
|||
Included Accessories | Power cable, Ferrite core, Ruber stoppers (4), Operation Manual |
*1 These characteristics are measured with A-weighting filter and/or 30kHz LPF.
Analog Input Characteristics
Input Terminal | Actual Load Impedance |
For Use With Nominal |
GAIN | Input level | Connector in Console | ||
---|---|---|---|---|---|---|---|
Nominal | Max.before clip | ||||||
ANALOG INPUT | 20kΩ (BAL) | 150Ω Lines | 0dB | +4dBu (1.23 V) | +24dBu (12.28V) | D-SUB Connector 25P (Female) | |
+12dB | -10dBV (0.32 V) | +10dBV (3.16V) | |||||
10kΩ (UNBAL) | 600Ω Lines | 0dB | +4dBu (1.23 V) | +24dBu (12.28V) | D-SUB Connector 25P (Female) | ||
+12 dB | -10dBV (0.32 V | +10dBV (3.16V) |
Analog Output Characteristics
Output Terminal | Actual Source Impedance | For Use With Nominal |
GAIN SW | Output level | Connector in Console | |
---|---|---|---|---|---|---|
Nominal | Max.before clip | |||||
ANALOG OUTPUT | 75Ω(BAL) | 10kΩ Lines | 0dB | +4dBu (1.23 V) | +24dBu (12.28V) | D-SUB Connector 25P (Female) |
-6dB | +18dBu (6.16 V) |
Digital I/O Characteristics
Terminal | Format | Data length | Level | Connector in Console | |
---|---|---|---|---|---|
AES/EBU | AES/EBU Professional use | 24bit | RS422 | D-SUB Connector 25P (Female) | |
Primary/Secondary | Dante | 24bit | 1000Base-T | RJ-45 x 2 | |
Cascade | - | 32bit | LVDS *2 | RJ-45 x 2 |
Control I/O Characteristics
Terminal | Level | Connector in Console | |
---|---|---|---|
WORD CLOCK | IN | TTL/75Ω terminated | BNC Connector |
OUT | TTL/75Ω | BNC Connector | |
System Link Out | 1.0±0.2Vp-p/75Ω *3 | BNC Connector |
*2. Hi Speed CML
*3. AES-3id
DANTE Accelerator (AIC128-D)
General Specifications
PCI Express card | Compatible with PCI Express x4 slots v1.0 and above |
---|---|
Audio channels | 256 channels (128 in/128 out @ 96 kHz or less) 128 channels (64 in/64 out @ 176.4 kHz or more) |
Supported Sample Rates | 44.1, 48, 88.2, 96, 176.4, and 192kHz |
Pull-up/Pull-down | +4.1667, +0.1, -0.1, and - 4.0 % |
Sample bit-depth | 24 bit |
Dante Network interface | Gigabit (1000Mbps; 1Gbps) Ethernet RJ45 port x2 |