Tio1608-D2 I/O Rack

Tio1608-D2
Sampling frequency rate External 44.1kHz, 48kHz, 88.2kHz, 96kHz
Signal delay Less than 1.3ms INPUT to OUTPUT, connect with DM3, Dante Receive Latency set to 0.25ms (one way), Fs=96kHz; Less than 2.6ms INPUT to OUTPUT, connect with DM3, Dante Receive Latency set to 0.25ms (one way), Fs=48kHz
Total harmonic distortion Less than 0.2% +4 dBu@20Hz-20kHz into 600Ω, Gain=+66 dB / Less than 0.05% +4 dBU@20Hz-20kHz into 600Ω, Gain=-6 dB, INPUT to OUTPUT, Fs=88.2kHz, 96kHz; Less than 0.1% +4 dBu@20Hz-20kHz into 600Ω, Gain=+66 dB / Less than 0.05% +4 dBU@20Hz-20kHz into 600Ω, Gain=-6 dB, INPUT to OUTPUT, Fs=44.1kHz, 48kHz *Measured with a -18 dB/octave filter @80kHz
Frequency response +0.5, -1.5 dB 20Hz-20kHz, refer to the nominal output level @1kHz, INPUT to OUTPUT
Dynamic range 108 dB, INPUT to OUTPUT, Gain=-6 dB / 110 dB, DA Converter, Fs 96kHz; 108 dB, INPUT to OUTPUT, Gain=-6 dB / 112 dB, DA Converter, Fs 48kHz
Hum & noise level Equivalent input noise -128 dBu, Gain=+66 dB, Fs 96kHz, 48kHz *Measured with A-weighting filter
Residual output noise -86 dBu, Fs 96kHz / -88 dBu, Fs 48kHz, ST main off *Measured with A-weighting filter
Crosstalk -100 dB, adjacent INPUT/OUTPUT channels, Input Gain = -6 dB *Measured with a -30 dB/octave filter @22kHz
Heat dissipation 100-240V, 50/60Hz, 43.5kcal/h
Power requirements 100-240V, 50/60Hz
Power consumption 50W
Dimensions W 480mm (18.9”)
H 88mm (3.5”)
D 364mm (14.4”)
Net weight 5.7kg (12.6lbs)
Accessories Owner’s Manual, Power Cord (2.5m), Rubber stoppers (4)
Others Temperature Range: Operating temperature range: 0 - 40℃, Storage temperature range: -20 - 60℃

Analog Input Characteristics

Input Terminals GAIN Actual Load Impedance For Use With Nominal Input Level Connector Balanced / Unbalanced
Sensitivity *1 Nominal Max. before clip
INPUT 1-16 +66 dB 7.5kΩ 50-600Ω Mics & 600Ω Lines -82 dBu (61.6μV) -62 dBu (0.616mV) -42 dBu (6.16mV) Combo Jack (XLR-3-31 type *2 or TRS phone *3) Balanced
-6 dB +10 dBu (245mV) +10 dBu (2.45V) +30 dBu (24.5V)

In these specifications, 0 dBu = 0.775Vrms.
+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.
*1. Sensitivity is the lowest level that will produce an output of +4 dBu (1.23V) or the nominal output level when the unit is set to maximum gain.
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND

Analog Output Characteristics

Output Terminals Actual Source Impedance For Use With Nominal Output Level Connector Balanced / Unbalanced
Nominal Max. before clip
OUTPUT 1-8 75Ω 600Ω Lines +4 dBu (1.23V) +24 dBu (12.3V) XLR-3-32 type *1 Balanced

In these specifications, 0 dBu = 0.775Vrms.
*1. 1: GND, 2: HOT, 3: COLD

Digital Input & Output Characteristics

Terminal Format Data length Level Audio Connector
Primary / Secondary Dante 24bit or 32bit 1000Base-T 16ch (Tio1608-D2 to other devises)
8ch (Other devises to Tio1608-D2)
etherCON Cat5e